FAQ: How To Build A Thumper?

What liquid do you put in a thumper keg?

Some moonshine stills have a “thumper” or “doubler” between them and the condensor. This is a jar of sorts, half-filled with liquid (water, mash or tails).

What should I put in my thumper?

Fruit, herbs, or spices can be placed in the thumper where their essences are, in effect, steam-extracted along with the alcohol during this virtual second distillation.

How much does it cost to put in a thumper?

filling it about 1/4 full. The options are: left over mash, tails from a previous run, etc. But if you want the thumper to do what it is supposed to do (increase the alcohol % in the final product), there needs to be some kind of alcohol in the thumper. The higher the alcohol concentration, the better.

Do you heat the thumper keg?

Many moonshiners do prefer to heat the thumper. The alcohol does need to stay in vapor form to be able to rise into the condenser. Wood barrels are often preferred as thump kegs because of wood’s natural isolative abilities.

You might be interested:  Quick Answer: How To Build A Mallard Duck Nesting Box?

Can I put fruit juice in a thump keg?

Yes-this will work. You are not going to get an intense flavor but it will add a bit. I have added fruit with some heads tails and a gallon of the fruit wash to a a thumper on a few batches of brandy with good luck.

How many heads is 5 gallons of mash?

For the instant gratification seekers in the crowd, here’s the short answer: A 1 gallon run will yield 3-6 cups of alcohol. A 5 gallon run will yield 1-2 gallons of alcohol. A 8 gallon run will yield 1.5-3 gallons of alcohol.

What is the best yeast for moonshine?

Vodka Turbo Yeast has a low congener profile and a great sugar-to-ethanol conversion rate, making it the best yeast for vodka, high purity neutral spirits or moonshine alcohol.

Why is my moonshine blue?

Basically, this is caused by the alcohol vapor corroding the copper metal. As the copper is literally eaten away, fragments transfer into the moonshine batch, which ultimately gives it a bluish tint. It’s important to note that moonshine made with fruit is more likely to turn out blue.

How big should a thumper be?

How Big Should a Thumper Keg Be? A thumper keg should be 25% to 40% the size of your main boiler. If you plan to prime your thumper keg with a sizable charge (botanicals, low wines, wash, water, etc), use a thumper keg that is at least 50% the size of your main boiler.

Does a thumper need to be heated?

Preheating a thumper is not recommended, in order to be effective it must be heated with the steam from the main boiler. More like 1.5 runs really because if I strip run and load the boiler with low wines it actually comes out higher abv than just one run with the thumper.

You might be interested:  FAQ: How To Build A Gps?

Do you need a thumper to make moonshine?

Making moonshine with a thumper instead of a pot still is great because thumpers essentially perform two distillations in one—without stripping the flavor the way reflux distillation does. Depending on your thumper, it’s typical to plan to fill it about halfway with liquid.

Do you need a thumper on a still?

It was traditionally used in hillbilly stills to increase the alcohol content of the distillate because, traditional stills only output product with about a 50-60 percent alcohol content. In short, the answer to whether our stills need a thumper keg is: NO.

How does a Mason jar Thumper work?

When vapors are forced into the thumper, the keg uses waste heat from the still pot to function so gas that condenses into liquid can once again vaporize and rise into the condenser. Some thump keg materials are better at absorbing and keeping warm and as a result, these kegs work better.

Can you distill alcohol in aluminum?

Aluminum does not distill, so none of it will end up in your distillate. Its not an ideal material, you can‘t solder to it well, etc.

Leave a Reply

Your email address will not be published. Required fields are marked *